Hearthstone deck

List of the table of contents of this article:

• 1, Can the minimum system board of stm32f103c8t6 be used as the main controller of the drone?
• 2, The minimum system element of stm32 single-chip microcomputer?
• 3, stm32 The difference between the minimum system board and the development board
• 4、Is the pins of the minimum system of stm32 the same
5, s Which item is not included in the tm32 minimum system
• 6, stm32 minimum system has a buzzer

Can the minimum system board of stm32f103c8t6 be used as the main controller of the drone?

STM32F103C8T6 is a 32-bit single-chip microcomputer based on the ARMCortex-M kernel STM32 series. The program memory capacity is 64KB, the voltage is 2V~6V, and the working temperature is -40°C~85°C.STM32F103C8T6 is a single-chip microcomputer chip designed by STMicroelectronics.

STM32F103C8T6 is a single-chip microcomputer chip designed by STMicroelectronics. It adopts the Cortex-M3 kernel, the main frequency is 72MHz, and the memory includes 64KB flash memory, 20KBSRAM and 2KBEEPROM.

Prepare a PS2 controller and receiver, and two No. 5 batteries to power the PS2 controller. Prepare an STM32 development board and download line, and the main controller is STM32F103C8T6. Prepare a USB to TTL module to facilitate subsequent serial port debugging and observation of the phenomenon.

The programs of single-chip microcomputers run in RAM without special regulations. STM32F103C8T6 CAN BE INFORMED ACCORDING TO THE SUFFIX: 48 PINS, 20KB OF SRAM, 64KB OF FLASH (ROM).

First of all, we need to look at the communication mode between the steering machine control board and the single-chip microcomputer, such as serial communication or IIC, and then look at the communication protocol of the steering machine control board.

High performance: The ARM Cortex-M3 kernel of STM32F103C8T6 has high processing power and response speed, which can meet the requirements of most embedded control systems. Low power consumption: STM32F103C8T6 adopts advanced energy management technology and can operate in low-power mode, thus effectively reducing system power consumption.

The minimum system element of stm32 single-chip microcomputer?

The smallest system of a single-chip microcomputer, that is, which devices need to be connected at least, can make the single-chip microcomputer run normally. A single-chip microcomputer development board is "single-chip microcomputer + peripheral chip". It is entirely up to you to decide what functions a single-chip microcomputer development board needs to do.

STM32 minimum system usually consists of the following parts: single-chip microcomputer: STM32 series single-chip microcomputer is the core of the whole system and is responsible for processing and executing program code. Clock generator: used to generate the clock signals required by the system, including CPU clock, GPIO clock, timer clock, etc.

The smallest single-chip microcomputerSystem, also known as the single-chip microcomputer minimum application system, refers to a system that can be used to form a single-chip microcomputer with the least originals. The three elements of the smallest system of a single-chip microcomputer are power supply, crystal oscillation and reset circuit.

Clock circuit. The hardware components of the minimum system of STM32 mainly include: power supply circuit, reset circuit, debugging interface circuit, start circuit, excluding clock circuit components. The STM32 series is based on the ARMCortex-M3 kernel specially designed for embedded applications that require high performance, low cost and low power consumption. .

The minimum system has only 26 I/O ports, and there is only one port that can be used for PWM output. If you control 11 rudders at the same time, the efficiency is too low. It is recommended to group the rudder, and the synchronously adjusted rudder adopts common PWM control. If it can be divided into 6 groups or less, it is recommended to use the maximum system. Unify.

The difference between stm32 minimum system board and development board

1. Development board: minimum system + a large number of peripherals, such as: AD/DA, digital tube, liquid crystal, buzzer, stepper motor, clock electricity Road, temperature measurement, etc. Purpose: Learn the basic functions of single-chip microcomputers and do some relevant experiments.

2. And the minimum system board means that the least equipment required to realize this system, that is, except for the necessary peripherals and other equipment, everything else is gone. This kind is customized.

3. The development board is a circuit board used for embedded system development, which is composed of input device, output device, memory, data path bus, central processor and external resource interface and other parts.The core board is an electronic motherboard that packages the core functions of MINIPC. Therefore, the definitions and components are different.

Is the pins of the minimum system of stm32 the same

The pin functions of stm32 are as follows: GPIO pin, ADC input pin. GPIO pin: The GPIO pin in STM32 is mainly used for input and output digital signals, and the pin status can be controlled by programming. ADC input pin: used to connect analog input signals, such as temperature, light intenss, etc., and convert them into digital signals.

The range of the input level of the STM32 pin is ALVC, the input is less than 0, the input is greater than 2V, the high level is counted, and 8V in LV and ALVT is the low level.

A 0.1uF capacitive filter needs to be placed next to all power supply pins to filter out the noise clutter of the power supply. The light power supply is written so long that I can't write it. Reset the pin. Reset is to restart. The STM32 reset pin is a low-level reset and a normal working state, and the reset pin is a high-level.

stm32 minimum system does not include which item

stm32 minimum system does not have a buzzer. The minimum system of stm32 mainly has 6 parts: power supply module, crystal circuit, download circuit, reset circuit, boot circuit and filter circuit.

STM32 minimum system usually consists of the following parts:Single-chip microcomputer: STM32 series single-chip microcomputer is the core of the whole system, which is responsible for processing and executing program code. Clock generator: used to generate the clock signals required by the system, including CPU clock, GPIO clock, timer clock, etc.

Restore the factory settings. The stm32 chip has a flash memory thickness of 218K bytes. According to the relevant information of the query, the stm32 clearing chip is restored to the factory settings and emptying the original chip. The stm32 minimum system is composed of power supply, reset, clock, debugging/download interface and startup.

The pins of the minimum system of stm32 are the same. The stm32 minimum system is composed of power supply, reset, clock, debugging/download interface and startup. The power supply stm32 single-chip microcomputer is generally powered by 3V, and the capacitor plays the role of filtering.Reset STM32 reset pin is low-level reset, normal working state, reset pin is high-level.

Does the minimum system of stm32 have a buzzer

Development board: minimum system + a large number of peripherals, such as: AD/DA, digital tube, liquid crystal, buzzer, stepper motor, clock circuit, temperature measurement, etc. And so on: learn the basic functions of single-chip microcomputers and do some relevant experiments.

No. Stm32 cannot control the passive buzzer. So stm32g431 doesn't have a buzzer. The buzzer is mainly divided into two types: piezoelectric buzzer and electromagnetic buzzer, piezoelectric buzzer: piezoelectric buzzer is mainly composed of multi-resonant oscillator, piezoelectric buzzer, impedance matcher and resonance box.

The minimum system of single-chip microcomputer is characterized by a completely open system resources, which can achieve arbitrary experimental functions with other module boards or self-built user circuits. The interface design is flexible and easy to use.

Detection function. The stm32 single-chip microcomputer is connected to the rudder in wired mode. This connection system is the STM32F103C series minimum system + NRF24L01 wireless module + OLED display + buzzer + button follower. Among them, the wireless module of NRF real priority mode is mainly responsible for detecting the water level value. Then display the maximum value on the OLED.

It depends on whether you are stm32's F103, F104, f107, F204, F40X, etc. The price of different series of chips is different, but since you areThe door has been changed to F103, right? After all, the STM32F103 series is representative and very suitable for entry.

Development board: minimum system + a large number of peripherals, such as: AD/DA, digital tube, liquid crystal, buzzer, stepper motor, clock circuit, temperature measurement, etc. Purpose: learn the basic functions of single-chip microcomputer and do some relevant experiments.